AOC e2070Swn Przewodnik Instalacji Strona 1

(LED Backlight) /SWNLE2 70SWN 0E2 700

10 Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to you

11 Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1. Power 2. Analog (D-Sub 15-Pin VGA cable) To protect equip

12 Windows 8 For Windows 8: 1. Right click and click All apps at the bottom-right of the screen. 2. Set the “View by” to “Category”. 3. Click

13 4. Click DISPLAY. 5. Set the resolution SLIDE-BAR to 1600x900.

14 Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization

15 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1600x900.

16 Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPL

17 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PAN

18 Hotkeys Power/ AUTO When Power on, press button to do auto configure . When Power off, press button to turn on the monitor . When Po

19 LED Indicator Status LED Color Full Power Mode Green Active-off Mode Flickering Green

2 Safety ...

Driver Monitor Driver Windows 8 1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen. 3. Click on the “Cont

215. Click on the “Display” icon. 6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button. 8. Click th

22 9. Click the “Driver” tab. 10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver... “ and then click

23 12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the d

24 Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Contro

25 Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Select and click o

26 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Propert

27 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. S

28 Windows Vista 1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".

29 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration fo

3 Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throug

30 Windows 7 1.Start Windows® 7 2.Click on the 'Start' button and then click on 'Control Panel'. 3. Click on the 'Display

4 Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied t

5 Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a pe

6 Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauter

7 Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sur

8 Setup Contents of Box Power Cable Analog Cable MonitorMonitor Base Monitor Base CD Manual Stand

9 Setup Stand Please setup or remove the Stand following the steps as below. Setup: Remove: